NewPrjFull/ja

プロジェクト定義ページの2つ目のアイコンを押すと、全顎プロジェクトページが開きます。

このページでは、歯列矯正の症例、可搬式フレームワークの症例、またはその他の対顎のある／ない全顎のスキャンが必要な症例で使用する、全顎スキャンプロジェクトを作成できます。

プロジェクト定義ページには5つのセクションがあります。

歯の定義

最初のteeth（歯）のセクションでは、任意の歯をクリックして全顎を選択または選択解除します。

プロジェクト

Project（プロジェクト）セクションでは、一般情報を入力できます。

• 患者名
• ドクター名（オプション）
• メモ（オプション）
• リファレンスリムの使用有無を決めるチェックボックス

It is possible to write freely in the Doctor and Notes boxes. As for the Patient, it is possible to:

• Write freely in the box
• Create a new profile clicking on the Search/Create button
• Search the database for an already existing profile clicking on the Search/Create button

The Search/Create Button opens the following window:

This window allows to search the project database for already existing patients. A filter can be applied and, for those who use VDDS protocols, the research can be restricted to that specific database.

By clicking on the Create button, the following window opens:

The patient creation panel allows to input general information regarding the patient and the treatment, such as:

• The patient's name
• The patient's birth date
• The patient's sex
• The doctor's name
• The patient's insurance ID, where applies
• Some notes

Once all the information has been filled in, select Ok to accept the data or Cancel to discard the changes and go back to the project definition page.

Full Denture Scan

In this section it is possible to signal the software that the occlusal rim needs to be scanned for a full denture project.

Just click on the With Occlusal Rim box to activate this option.

CAD Integration

When the project is started directly from Exocad, the STL files produced in the scanning process will be transmitted to Exocad in just one click. On the other end, if the project gets created in the scanning software, the automatic export to CAD will not be configured, unless it is selected in this section.

By clicking on the No CAD box the CAD selection window opens

and it allows to choose one of the software integrated with our scanning system for automatic trasmission of the STL information.

• Exocad
• VDDS protocol (for orthodontics)
• Onyx Ceph (for orthodontics)

If No Cad is selected, the software will then ask the user to define an export path for the STL files.

Articulators

The last section allows to select an articulator to use the Dynamic Articulation Module.

If the Dynamic Articulation module is not active on the license this section will not be available

Remember that it is always possible to scan any kind of articulator, this section is only to be used if you want to scan with the dynamic articulation module and pass the occlusion position in the Virtual Articulator of Exocad.

The Articulators available in Exocad and therefore in our software are:

Artex 

to scan the Artex Articulator and to use the same in Exocad's Virtual Articulator

Sam/ Adesso 

to scan the Sam Articulator or the Adesso splitcast and to use the same in Exocad's Virtual Articulator

Protar- Kavo 

to scan the Kavo Articulator and to use the same in Exocad's Virtual Articulator

A7 - Bioart 

to scan the Bioart Articulator and to use the same in Exocad's Virtual Articulator

Denar by Whipmix 

to scan the Denar Articulator and to use the same in Exocad's Virtual Articulator

To start the project accept the definition with the button.

To find specific information on how to scan in Free / Expert mode, go to the Full Jaw Project example page.