Open main menu

Example: Orthodontic

Revision as of 09:24, 25 September 2017 by Meinan (talk | contribs) (Created page with "一方、前述のように、咬合させた2つのモデルを輪ゴムやワックスで固定してスキャンすることも可能です。")


このページでは、咬合する2つの全顎モデルをスキャンする例を、ウィザードに従って説明します。

Contents

プロジェクト定義

デスクトップのScanWayアイコンをダブルクリックして、スキャンソフトウェアを起動します。ようこそページが開きます。プロジェクトを作成するには、最初のアイコンをクリックします。

 

プロジェクトの定義方法について詳しくは、新規プロジェクトの作成のページを参照して下さい。

今回のデモ用プロジェクトでは以下の通り定義します。

 

ステップ1: 咬合器スキャン

両顎を持つように設定されたすべてのプロジェクトの最初のステップは、咬合器スキャンです。

咬合器スキャンでも、常に咬合器をスキャンする必要はありません。このスキャンに必要なのは、専用サポート上の咬合器を使った咬合スキャン、またはモデルホルダー上での2つのモデルの咬合スキャンです。

ユーザーが咬合器をスキャンする必要がある場合は、後ろへ傾けることをおすすめします。こうすることで、できるだけ多くの情報を得ることができるようになります。傾けることができない咬合器もあるので、その場合は不要です。

 

スキャンインターフェースのライブビューでは、咬合器が実際にまっすぐ置かれていると、咬合状態を正確に取得するのが難しくなることが確認できます。

 

一方、前述のように、咬合させた2つのモデルを輪ゴムやワックスで固定してスキャンすることも可能です。

 

Once the objects have been placed in the scanner (either the articulator or the models one on top of the other), the scan can be started with the Scan Button . Once the scan is finished the result will be shown.

 

For further information on the other available functions check the Scan Interface page.

Click   to access the second step of the wizard.

Step 2: Lower Model

The second step of any project that has been set to have both jaws, is the Lower Model Scan. All steps, except for the articulator one, include two sub-steps: the actual scan and the edit of the acquired image.

Scan Step

Place the lower model on the model holder and click the Scan Button . Once the scan is finished the result will be shown.

 

This scan has been performed with the Reference Rim. Everytime the user launches a scan for models, dies or markers, if the software recognises that the reference rim has not been used the following message shows.

 

The user can therefore decide whether to cancel the scan, put the reference rim on the model holder and start a new scan, or to scan without using the reference rim. For information on the reference rim visit the Accessories page.

Click   to access the second part of the Lower model step.

Edit Step

This step allows to edit the acquired image; for detailed information on all the available options in this step visit the Edit Tools page.

The image at this step can be both edited or trimmed. At this stage it is actually important not to edit too much the image or cutting big chunks of information, since it would make it more difficult for the software to calculate the automatic alignment of the object to its reference.
In this case, to trim the object, the base cut tool has been used and accepted by double clicking on the model.

 

When you are satisfied with the result click   to access the next wizard step.

Step 3: Upper Model

The upper model Scan, like the lower model, requires the user to undergo two steps.

Scan Step

Place the upper model on the model holder and click the Scan Button . Once the scan is finished the result will be shown.

 

As before, if the reference rim is not placed on the model holder, the software will show the relevant message.

Click   to access the edit step for the Upper model.

Edit Step

The upper model can still be edited as shown for the lower model. This time, we will edit the image using a selection tool and cutting with the delete button on the keybord.

 

When you are satisfied with the result click   to access the next wizard step.

Save and Align

Immediately after having pushed the   button, the software saves and tries to align automatically the scanned items to their reference.

To learn more on the automatic alignment and the manual procedure visit our Alignment Interface page.

Step 6: Mesh Generation and Export

At this point the software immediately starts mesh generation. The meshes can be edited and exported individually or as a unique image. To learn more about mesh editing visit our Mesh Tools page.

Click on the Export Button   to export to CAD and select the folder to save the STL files.